Your cart is empty!
Data & Telecommunications test and measurement equipment is available for you to rent for short or long term. Often we will add equipment to our rental inventory if there is a specific requirment for equipment we do not have in the rental fleet.
Anritsu MT9083A2 Access Master quad wavelength OTDR. 850/1300 nm (29/28 dB) and 1310/1550 (39/37.5 dB). Singlemode port is SC/APC. Intelli..
Complete testing of PON-based FTTx networks featuring up to 1x64 splits or single fibre runs. 1310, 1550 and 1625nm wavelengths. Intellige..
Ethernet/Gigabit Ethernet loopback unit ETS-1000L (referred to as unit, analyzer) is intended for performing loopback at the physical, da..
It is optimized for FTTx E & GPON. PPM350B has 10 user-definable threshold sets, each set consisting of three wavelengths (1310, 1490..
Kit includes PPM-352B-EG-ER optimized for FTTx E & GPON & FIP-400 inspection probe with handheld display. PPM352 has 10 user-defi..
Hand-held fusion splicer, can splice from 1 to a maximum of 12-ribbon fibre. Protection sleeve shrink time is 35 seconds for ribbon fibre..
S178 hand-held, core-alignment fusion splicer and S325 cleaver. Splicer provides typical losses of 0.02dB & 0.01dB on single & mu..
The Fitel S179 is a handheld core-alignment fusion splicer for single and multimode fibres. It includes an S326 cleaver. Typical 6 s splice ..
Fluke multimode (CFP-MM-ADD) optical loss test set modules for the Versiv DSX-5000. Provides Tier 1 certification at 850 and 1300 nm in 3 ..
Fluke multi and singlemode (CFP-Q-ADD) optical loss test set modules for the Versiv DSX-5000. Provides Tier 1 certification at 850, 1300,..
Fluke CFP-SM optical loss test set modules for the Versiv DSX-5000. Provides Tier 1 certification at 1310 and 1550 nm in 3 s. A set refer..
The Fluke DSX-5000QOi contains the DSX-5000 copper analyser, CertiFiber Pro OLTS quad wavelength, Optifiber Pro OTDR quad wavelength, and..
The Fluke DSX-5000 1 GHz cable analyser copper test solution enables testing and certification of twisted pair cabling for up to 10 GigE ..
Cable certification tester up to 900MHz. Tests to Category 3, 4, 5, 5E, 6, 6a and 7. Cable analyzer for use with shielded and unshielded t..
DTX1200/1800 singlemode fibre interface. Use for testing fibre installations in local area networks. Fits in the slot on the back of DTX c..
The FI-7000 FiberInspector Pro is a fiber optic inspection scope that allows you to inspect and certify fiber optic connector end-faces in..
Fluke SimpliFiber FTK1000 fibre test kit. Light source is multimode 850nm and 1300nm. Power meter has 850/1300nm multimode and 1310/1550n..
The FI-1000 FiberInspector kit enables you to quickly inspect and certify fibre end-faces inside ports or patch cords. It's 2-second autom..
Measures wavelengths 850 and 1300 nm. Designed for testing, troubleshooting and certifying multimode 50 and 62.5 µm fibre optic networks...
Fluke Optifiber Pro Quad multi and singlemode OTDR, wavelengths 850, 1300, 1310 and 1550nm, dynamic range 28, 30, 32 and 30 dB respectively...
Fluke singlemode OTDR designed for testing, troubleshooting and certifying network fibre optics at 1310/1550. Equipment has SC interface ..
Ribbon fibre fusion splicer, will splice from 1 to 12 fibres. Splice time 20 sec, sleeve shrink time 40 sec, typically. Detachable work t..
Fujikura FSM60S Splicer & CT30 Cleaver For splicing multi and single-mode optical fiber. Battery and mains operated. Features splice p..
Fujikura FSM70R 12-core ribbon fibre fusion splicer. Typically splice time 15 s and sleeve shrink time 40 s. Detachable work table and ar..
Fujikura FSM70S single fibre core alignment fusion splicer and CT30A cleaver. Typical splice losses of 0.02 dB and 0.01 dB on single and ..
Field tester for the installation, commissioning and fault finding of fibre and copper SDH/PDH networks from 1.5Mb/s to 2.5 Gb/s. Optical..
Field tester for the installation, commissioning and fault finding of fibre and copper SDH/PDH networks. Electrical interfaces for PDH/SDH..
Field service tester for commissioning,maintenance and troubleshooting of E1 PCM2Mbit/s and V.11/RS-442, V.24/RS-232, V.35,V.36/RS-449, EI..
JDSU HST-3000 with Broadcom Bonded module (SIM) for complete copper testing from POTS to full spectrum Very High Speed Digital Subscriber..
JDSU,MTS-2000 with JDSMTS-4136MA-FCOMP-SCA OTDR module. Maintain metro and PON-based FTTx networks. 1310, 1550 and 1625 nm wavelengths at..
Maintain metro and PON-based FTTx networks. 1310, 1550 and 1625nm wavelengths at 42, 40 and 40 dB dynamic range (respectively), includes ..
Multirate interface for PDH-DS1/DS3/E1/E3/E4,STS-1 OC-3/12/48/48, STM-1e/1/4/16 and interface for OC-192 STM-64 with the ability to monit..
OLA-55 is a Smart, Future Proof Singlemode Optical Attenuator. Adjustable wavelength from 1260 to 1650 nm (1nm increments). Calibrated wa..
JDSU OLP-55 Optical Power Meter BN 2277/01 Power & Loss Measurement for installation, maintenance and repair of fiber optics networks..
OLS-55(BN 2279/01) Smart, Future Proof Singlemode Optical Light Source. Operates on dual wavelength of 1310nm and 1550nm. Output power is..
Light source (OLS-35) and power meter (OLP-35) fibre optic test set for singlemode applications 1310 and 1550nm. OLS-35 has interchangeab..
JDSU OLP-87 PRO is a FTTx/PON power meter with P5000i inspection probe. Used for qualification, activation, inspection and troubleshootin..
JDSU/Viavi handheld field tester for the installation and commissioning of E1 and Datacom services. Applications include (not limited to)..
Kingfisher singlemode light source KI-28010 and power meter KI-2600. Compatible with APC and PC singlemode networks. Wavelengths 1310, 15..
Included are two KI73410 for bi-directional two-way Insertion and Optical Return Loss testing at 1310, 1550 and 1625nm with angled connec..
Light source (KI7827) and power meter (KI7600) optical fibre test set for singlemode applications such as FTTH (1310, 1490 and 1550nm). L..
Kit consists of Encircled Flux (EF) compliant test reference leads for the following fibre networks:
- SC, ST 62.5 um (OM1 & 2..
The Netscout AirCheck G2 is a simple to use, handheld wireless tester that allows users to quickly verify and troubleshoot 802.11 a/b/g/n..
The CM3000 analyses upstream and downstream network performance for business, bundled services and validates the effectiveness of DOCSIS ..
VeeEX MX100e+ is a full-featured Next Generation Mobile Backhaul and Carrier Ethernet Tester. Supports 10/100/1000Base-T on RJ45 port, 10..
The CX350s supports legacy analog CATV signals, HD DVB-C carriers, DOCSIS 3.0 and 3.1 cable modem emulation/measurement including a ..
The TX130+ platform offers customers a single, multifunctional access network diagnostic tool. The TX130+ is designed for field engineers..
The TX130+ with Datacom offers customers a single, multifunctional access network diagnostic tool. The TX130+ is designed for field engin..
The TX130+ platform offers customers a single, multifunctional access network diagnostic tool. Equipped with PDH/DSn, Datacom and Etherne..
The VePAL TX130M+ is a full-featured Mobile Backhaul test solution supporting legacy PDH/DSn, Carrier Ethernet technologies, and Synchron..
The Viavi OneExpert CATV 620 is an approved signal analysis meter for verifying and troubleshooting network performance on the NBN and Telst..
The Viavi (formerly JDSU) OneExpert DSL is designed for testing and qualifying POTS to full spectrum Very High Speed Digital Subscriber L..
The Viavi SmartClass Ethernet tester is used for the installation, turn up, and maintenance of Ethernet IP services up to 1 Gbit electric..