Your cart is empty!
Rent Industrial Process Calibrators including major brands such as Beamex, Crystal, Druck, Emerson and Fluke. General Industrial equipment available for short term or long term rental.
Beamex external pressure modules compatible with MC6, MC5, MC4, MC2 MC5-IS, MC2-IS and MC5P calibrators. Various rangers available, please i..
NATA certified MC6 provides calibration capability for pressure, temperature, electrical and frequency signals. HART communication and CM..
NATA certified MC6 provides calibration capability for pressure, temperature, electrical and frequency signals with HART communication and D..
Fully self-contained pressure test and calibration system combines pressure generation, signal measurement and loop power. Generates from..
Fully self-contained pressure test and calibration system combines pressure generation, signal measurement and loop power. 0 to 200 ba..
Druck DPI 620 Genii advanced modular pressure calibrator with HART, includes pneumatic pressure station with 1/8 BSP(G) or 1/8 NPT test p..
Fully self-contained pressure test and calibration system combines pressure generation, signal measurement and loop power. 0 to 100 bar, acc..
Hydraulic pressure calibrator including pump and current voltage standard. Pressure range 0 - 350 bar (5000 psi) +/- 0.005% FS. Voltage inpu..
Fully self-contained pressure test and calibration system combines pressure generation, signal measurement and loop power. 0 to 70 bar, accu..
Fully self-contained pressure test and calibration system combines pressure generation, signal measurement, and loop power. Generates fro..
Druck DPI620 Genii advanced modular pressure calibrator with HART, includes hydraulic pressure station with 1/8 BSP(G) or 1/4 NPT test po..
Druck PV211 Pneumatic Hand Pump. 40 Bar pneumatic pressures and vacuum to -0.95 Bar. Comes with Precision Vernier for fine pressure adjust..
Druck PV212 Hydraulic Hand Pump. Provides up to 700 Bar hydraulic pressure...
Provides up to 700 Bar hydraulic, 40 Bar pneumatic pressures and vacuum to -950 mBar. Built-in stroke adjuster, lower pressure fine contr..
Will configure, test, and diagnose your HART and Foundation FieldBus devices. Able to communicate with any device, by any manufacturer. I..
The Emerson AMS Trex is an intrinsically safe HART and Foundation Fieldbus device communicator. It allows technicians to configure, isola..
Intrinsically safe HART device communicator. Allows technicians to configure, isolate, diagnose and repair problems while devices continue t..
Fitting set (max pressure = 10,000psi) for pressure calibrators. Female connector sizes:- 1/4"BSP & NPT; 1/8"BSP & NPT; 3/8"BSP &..
DC voltage measurement 0.025%, 300V max, source 0.02%, 11V max. DC current measurement 0.025%, 110mA max, source 0.01%, 22 mA max. Resist..
Documenting process calibrator. DC voltage msmt. 0.025% 300 V max, source 0.02% 11 V max. DC current msmt. 0.025% 110 mA max, source 0.01..
Precision Multifunction Process Calibrator. DC voltage msmt. 0.010% 30 V max, source 0.010% 20 V max. DC current msmt. 0.010% 24 mA max, ..
The Fluke 726 precision multifunction process calibrator is designed specifically for the Process industry with broad workload coverage, ..
Fluke 753 calibrators provides simultaneous source and measure volts, mA, thermocouples, RTDs, frequency, ohms and pressure to calibrate ..
Fluke 754 with HART offers simultaneous source and measure capabilities for all common process parameters. Measure/source volts, mA, RTDs, ..
Measure 4-20 mA control lines, PLC loops, transmitters or any 4-20 mA line without breaking the loop. Capable of 0-20.99 mA and 24-100 mA..
Standard multimeter functions with 2 to 20mA sink and source capability, including a 24V supply. HART 250 resistor, 20mA drive into 1,200..
The PROFIBUS Tester 5 (BC-700-PB) is a powerful diagnostic and troubleshooting tool for testing cables, measuring signals and analysing the ..